Trang nhất » Sản phẩm » Controller » GGM


                  Xem ảnh lớn

Speed Control Pack

Mã sản phẩm: S000129

* 1. Applicable motors are Speed Control Series Motors of ours. * 2. The electric brake does not have holding torque. * 3. Please purchase our GSA-1 / GSA-2 Type Control, if you need the functions of SLOW RUN and SLOW STOP.

Giá: Liên hệ
MODEL GPA-1, GPA-2
 
 
 
g
 

GPA-1 GPA-2
Rated Voltage Single-PhaseAC100/110V Single-PhaseAC200/220V
Operation Voltage
Range
±10% (compared with Rated Voltage)
Power Frequency 50/60Hz
Rated Current 0.1A~2.2A 0.1A~1.0A
Applicable Motor1
Output
6W~90W 6W~90W
Speed Control Range 60Hz : 90~1700r/min
50Hz : 90~1400r/min
Speed Variation 5% (standard)
Speed Setting
Device
Built in Type (possible to install an external speed setting
device attachable : special order)
Braking Possible to stop brake for some period by electric brake
Electricity Braking
Period
0.5sec (standard)
SLOW RUN
SLOW STOP
non
Operation
Temperature
-10~50℃
Storage Temperature -20~60℃

* 1. Applicable motors are Speed Control Series Motors of ours.
* 2. The electric brake does not have holding torque.
* 3. Please purchase our GSA-1 / GSA-2 Type Control, if you need the functions of SLOW RUN and SLOW STOP. 

 
- It is possible to vary the revolution speed of the motor by the speed setting device of the upper side of the product.
- The thick solid line indicates the power source circuit. Please use about 0.75mm2 wire. 
- In case the service wire of T.G. is long (over 1 m), connect the twist sealed section with ② terminal.
 




 


 
1. In case of the thick sold line, the motor rotating direction is CW when viewed from output shaft. When adjusting
to CCW, change red and white wire of the motor, and then connect them. 
2. Yellow wire is the connection of a fan motor. If the output of the motor is greater than 60W and it is applicable.


 
1. Set "STOP" period for induction motor and switch SW2 after rotation has stopped.
2. Reverse motor does not need "STOP" period. It has no relation operating SW2 when SW1 is on.
3. Yellow wire is the connection of a fan motor. If the output of the motor is greater than 60W and it is applicable.



 
1. In case of the thick sold line, the motor rotating direction is CW when viewed from output shaft. When adjusting 
to CCW, change red and white wire of the motor, and then connect them. 
2. When Switched from RUN to STOP, electric brake will function about 0.5 sec and motor will come to stop 
instantaneously. 
3. Yellow wire is the connection of a fan motor. If the output of the motor is greater than 60W and it is applicable. 

 
1. When Switched from RUN to STOP, electric brake will function about 0.5 sec and motor will come to
stop instantaneously. 
2. Do not operate SW3, SW4 for this 0.5 sec.
3. Changing period of SW3, SW4 should be done quicker than STOP to RUN of SW2, SW5.

 
 
1. Please set up the scale of the speed setter of the main body as (Low).
2. Please wire as shortly as possible.
3. Use shielded wires and connect to Terminal No. ② of Control Pack.


 

1. This wiring for uni direction +variable speed + braking of motors 25W or less. For motors 40W and over  part 
of wiring is different. Refer to the electrical wiring diagram for the corresponding connection.
2. Input time of SW1 should be about 0.5 sec. earlier than SW4.
3. Set the volume "LOW" and use external volume VR to control speed.
4. When not in use for long period turn SW1 off.

 
 
1. Set the stop period to stop and convert to SW3 after rotation has stopped.
2. Input period of power switch SW1 should be about 0.5 sec. faster than the signal of start operating of SW2, SW4.
3. When RUN/STOP, operate with SW2, SW4 while SW1 is on. Even with small signal it can control the motor.
4. Set the volume "LOW" and use external volume VR to control speed.

Sản phẩm này không có hình ảnh khác
Số ký tự được gõ là 250

Sản phẩm cùng loại

 
      

Trang chủ        |     Giới thiệu        |       Sản phẩm       |        Tin tức - Sự kiện       |       Tuyển dụng     |     Download      |      Liên hệ

 
I-motion Vietnam CO., Ltd
Add: 90/2 Phan HUy Ich st, Ward 14, Go Vap Dist, Ho Chi Minh City, VN
Phone: 08.39470421 Fax: 08.3947 0454
Email: lhk@imotionasia.com.vn
Website:
www.imotionasia.com.vn
I-motion Pte Ltd
Add: Blk 3026, #02-148 Ubi Road 1 Singapore 40879
Tel: +65-6841 7877
Fax: +65-62803655

Cửa lưới chống muỗi | giàn phơi thông minh | khung bảo vệ cửa sổ | lưới an toàn ban công gian phoi cua luoi